Wheels

DT Swiss Standard Front Quick Release Skewers. - Traditional cam-operated lever - Stainless steel shaft

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 40mm

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 63mm

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 73mm

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

- Extra security against theft - 5mm hex CrMo axle

Using Easton End Caps allows you to utilize the versatility of Easton Wheels. Easton wheels are interchangeable with a variety of wheel mounting standards.

Pawl and spring kits for Easton hubs.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Grade 10 chromium steel balls

- 10mm axle holes for mountain bike applications - 14mm axle holes for BMX applications - Heavy duty steel protects frame, tensions chain - M8 threading, Nylock nut

- 14 gauge forged 7075 alloy with CNC finish - Matches Halo and Gusset anodized colors perfectly - Sold in bags of 50 - length: 12mm

- Precision CNC machined 6061 aluminum axle nuts - Compare stock steel nuts at 44 grams versus alloy nuts at 16 grams

- 15 x 100mm thru-axle endcaps for Spin Doctor 6F (front)hub - 20 x 110mm thru-axle endcaps for Spin Doctor 6F (front hub - Conversion kits for Spin Doctor 6-Drive hubs are not compatible with original Spin Doctor and Spin Doctor Pro hubs

- Non-quick release design for added security - Alloy anchor nut includes Anti-Spin tab which prevents unwanted turning of nut when tightening or loosening the hex through-bolt - XL version compatible with thicker dropouts (up to 10mm thick) - Torque to 7 N - Wheel: front/rear - Spacing (front/rear): 100/135mm - Shaft: Chromoly

- Front axle conversion, 15mm thru-axle, Wide Boy - Conversions for fitting a Wide Boy hub onto either a 15mm or 20mm thru-axle fork

- Rear axle conversions for Spin Doctor Pro rear hub - Various replacement axles and conversion kits for Spin Doctor and Spin Doctor Pro hubs - Some conversions utilize pre-existing axle components for retrofit - Conversion kits for original Spin Doctor and Spin Doctor Pro hubs are not compatible with Spin Doctor 6-Drive hubs

- Rear axle replacement kit, 10mm nutted, DJD-SupaD - Spin Doctor, Spin Doctor Pro and Spin Doctor 6-Drive parts are generally not cross compatible - DJD and DJD-BD parts are generally not cross compatible

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

- High-quality fat bike rim strips - Super durable PVC material

Origin-8's Torq Lite Track Cog Lock Ring 1.29" x 24 tpi with left-handed threaded thread is the only lock ring you need. Hardened threading and extra material make this highly durable to help you go the distance.

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.

Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061

Parts for RaceFace hubs.

These bobbins are made by the Robert Axle Project and are identical to the bobbins that came with your original BOB skewer. Slide them on your axle ends to complete your Robert Axle thru axle for BOB Trailer. - Sold in pairs - Manufactured from 303 Stainless Steel - Includes stainless steel hardware for attaching to axle